A. EMERGENCY TREATMENT
1. keep airway
- foreign body에 의해 airway obstruction이 발생하였을 때는 즉시 손가락이나
흡인기를 이용하여 기도내 이물을 제거해야 한다
- 다발성 외상이나 안면골 골절 시는 심한 부종으로 airway obstruction이 발생할
수 있으며 이 때는 nasotracheal intubation을 하고 이것이
1. Pump에서의 Cavitation (공동현상) 에 대하여 기술하고 이로 생길 수 있는 문제점과 그 방지책에 대해 논하시오
- Cavitation이란
유체가 넓은 유로에서 좁을 곳으로 고속 유입하거나 벽면의 요철, 만곡부 등으로 흐름이 직선적이지 못할 때 유체는 저압이 되고 포화증기압보다 낮아지면 기화되어 기포가
Ⅰ. 개요
우리 경제는 급속한 발전과 구조변화를 이룩하여 왔다. 실제 공업부문은 연평균 16.4%의 실질 성장을 실현하여 한국 경제 의 고도성장을 주도하였으며, 세계수준에서도 가장 높은 성장실적을 기록하였다.
한국산업의 발전은 정부 주도형 산업정책과 수출 지향적 개발전략에 크게 의존하였다
(1) Project Objective
To develop a new commercial product that is valuable, feasible, and practical in the real market.
(2) Deciding The Market for The New Product
In this world, there are myriad markets, consumers, products. However, considering our company's technologies(internal factor) and marketability(external factor), we chose the market of kitchen utensils for our new product.
plasticity), 그 변형을 소성변형(塑性變形 ; plasticdeformation)이라 한다. 이와 같은 재료의 소성을 이용하여 가공하는 것을 소성가공(塑性加工 ; plastic working)이라 하며, chip을 생성하지 않는 주조, 용접에 이어 비절삭가공의 일종이다. 소성가공으로 재료를 변형시켜 목적하는 형상과 치수를 얻을 수 있고, 재
1. abstract
The purpose of this experiment is to measure the elasticity about the tensile force, the plasticdeformation resistance and breaking strength of the materials through MTS.
And I analyzed the result and compared the theoretical and experimental values. Also, I contemplated these results why there is a difference between them.
2. 실험목적
재료를 잡아 당
The purpose of this experiment can draw the optimized design by measuring the tension tester that measure the elasticity about the tensile force, the plasticdeformation resistance and breaking strength of the materials.
If we design safety, we should use the ductile material.
.
대부분의 구조물은 사용 중에 힘(하중)을 받게 된다. 그러므로 우선적으로 구조물재
deformation curve: 인장실험에서 직접 얻어지는 것은 load deformation 와의 관계 curve이다.
================중략=====================
5. 결론 및 토의
시험편의 인장하중 - 변형량 관계를 측정하여 항복점, 인장강도, 탄성계수, 변형도, 단면감 소율 등의 기계적 성질을 알아보는데 이 실험의 목적이다. 만능 시험기에서
deformation curve: 인장실험에서 직접 얻어지는 것은 load deformation 와의 관계 curve이다.
================중략=====================
5. 결론 및 토의
시험편의 인장하중 - 변형량 관계를 측정하여 항복점, 인장강도, 탄성계수, 변형도, 단면감 소율 등의 기계적 성질을 알아보는데 이 실험의 목적이다. 만능 시험기에서
재료에 힘을 가하면 재료에는 변형이 생긴다. 이 힘이 작으면 힘을 제거하였을 때 원상태로 복귀하지만 힘이 재료가 버틸 수 있는 한계점을 넘으면 힘을 제거하여도 재료가 복귀되지 않고 변형이 남게 된다.
이와 같이 변형이 남는 영구적 변형을 소성변형(PlasticDeformation)이라고 하고, 이러한 영구 변